Florida Sidecar Products
9038 S.R. 52
Warehouse
Hudson, FL
United States
ph: 1-727-856-2836
Mark
Genuine New Old Stock California Sidecar Mounts and subframes. I went to the California Sidecar factory December-13-2018 and purchased all their sidecar parts that had been in storage since 2010. I filled a large moving truck with all the parts. Listed on other pages will be parts and sidecar frames.
Payment: I do not have a shopping cart so for each purchase please click on each paypal button. Or e-mail me a list of parts you want and I can send a invoice to make the purchase or send a check.
Here I'm at the California Sidecar factory in Virginia going back to Florida with a truck full of new sidecar parts. The Trike show room is on the left side of the picture. Yes that white stuff is snow. They had about 14" a few days before I was there.
Sidecar Frame I-bolt for all California Sidecar frames, Friendship III, FS II SE, FS II, FS I, Companion GT, Companion, etc. I-bolt head has 3/8" bolt hole to attach strut to. Theads are 3/4"-16 tpi. Threaded section is 3-3/8" long. I-bolt is 5-3/8" long overall. Comes with nylon lock nut. CSC OEM part # S009.
$33. each plus shipping.
email me for world wide shipping cost.
1-1/4 inch motorcycle frame sidecar U-clamp mount assembly with frame shim. Zinc plated. CSC New Old Stock. The I-bolt hole is 3/8". I-bolt head is 1/2" thick. I-bolt threads are 3/4"-16 tpi
Free shipping in the USA.
email me for word wide shipping cost.
1-1/2" motorcycle frame sidecar mount assembly with motorcycle frame shim. Zinc plated. CSC New Old Stock. I-bolt head is 1/2" thick and bolt hole is 3/8". I-bolt threads are 2-3/8" x 3/4"-16 tpi. The stud is very long, 2-3/8" on this I-bolt. It was made for the Honda Goldwing 1500 frame to be able to reach thru the plastic cover on the motor. The frame shim is 3" long. The zinc plating is ruff from being in storage since 2010.
Free shipping in the USA.
email me for world wide shipping cost.
Notched motorcycle frame, sidecar mount. Fits 1-1/4" motorcycle frames, Harley,etc. This is for getting in tight places. The back is 1-1/2" high and the front is 2" high. Comes with frame shim. I had to enlarge some of the small bolt holes to get the mounting block to fit in the strap.
Free shipping in the USA.
email me for world wide shipping cost.
For use on U-clamp mount and on some strut ends. Bolt hole is 3/8''. Threads are 3/4''-16 tpi. Part # S008 CSC OEM NOS.
Free shipping in the USA.
email me for world wide shipping.
California Sidecar Bent (curved) strut. This is used on the front mount so you can get your foot under strut to use the brake pedal. Also used on the rear for the passenger floorboard to give them room. This is just the strut tube 1-1/2" O.D. no clevis ends. This is a OEM NOS CSC part #S020-1
Free shipping in the USA.
e-mail me for world wide shipping cost.
Chrome sidecar straight strut assembly. The main strut tube is 9 inches long with a 1-1/2" O.D. With the two clevis ends installed strut at it shortest is 14 inches. At its longest with both clevis bolts screwed out it is 21 inches long.Clevis bolt hole is 3/8". Strut threads are 3/4"-16 tpi.
Free shipping in the USA.
email me for world wide shipping cost.
12" straight chrome strut. The main strut tube is 12" long with a 1-1/2" O.D. With the two clevis bolts screwed in all the way it is 16-1/2" at its shortest. And with the clevis bolts screwed out it is 24 inches at its longest. Clevis bolt hole is 3/8". Strut threads are 3/4"-16 tpi. CSC NOS.
Free shipping in the USA.
email me for world wide shipping cost.
Bent chrome strut with clevis ends. This strut lets you get your foot under the strut to use the brake pedal and also is used so your passenger can get their foot on the rear floorboard.
Strut tube is 1-1/2" O.D. With clevis bolts screwed in all the way it is 15-3/4" straight from bolt hole to bolt hole. With clevis ends screwed out all the way it is 22-1/2" straight from bolt hole to bolt hole.Clevis bolt is 3/4"-16 tpi. Clevis bolt hole is 3/8".
Free shipping in the USA.
email me for word wide shipping cost.
Below is the new clevis bolt I have in stock. Made from a solid piece of steel and zinc plated.
Clevis Bolt: Strut ends. Screws into strut. Threads are 4-5/8'' long by 3/4''-16 tpi.. Clevis I.D. is ½'' with a 3/8'' bolt hole. Part # S022.
Free shipping in the USA.
email me for world wide shipping cost..
2 inch offset lower slip tube mounting clamp. This part slides into the sidecar frame. Bolts are 1/2". The tube O.D. is 1-1/2". The inside of the clamp is 1-1/2". OEM CSC part and also fits Champion Sidecar frames and most American made sidecar frames.
Free shipping in the USA.
email me for world wide shipping cost.
90 degree adaptor clamp mount slides into the lower sidecar frame mounts. Bolts are 1/2", O.D of tube is 1-1/2". Clamp I.D. is 1-1/2". NOS OEM CSC and fits Champion Sidecar frames also and most American made sidecars. Powder coat is scratched from storage.
Free shipping in the USA.
email me for world wide shipping cost.
45 degree clamp mount is used with either the 90 degree adaptor or the 2" offset to reach the motorcycle mount at the right angle.
Pinch bolts are 1/2". O.D of tube is 1-1/2". Clamp I.D. is 1-1/2". NOS OEM CSC and fits Champion Sidecar frames also and most American made sidecars. Powder coat is scratched from storage.
Free shipping in the USA.
email me for world wide shipping cost.
70 degree clamp mount is used with either the 90 degree adaptor or the 2" offset to reach the motorcycle mount at the right angle.
Pinch bolts are 1/2". O.D of tube is 1-1/2". Clamp I.D. is 1-1/2". NOS OEM CSC and fits Champion Sidecar frames also and most American made sidecars. Powder coat is scratched from storage.
Free shipping in the USA.
email me for world wide shipping cost.
45 degree sidecar boss mount with heim joint is used with either the 90 degree adaptor or the 2" offset or a 45 degree clamp or 70 degree clamp to reach the motorcycle mount at the right angle and connect the heim joint to the lower clevis mount on the motorcycle.
Generally it is a combination of two or three slip tube mounts that are needed to get the right wheel lead and angles to attach the heim joint to the motorcycle mount.
O.D of tube is 1-1/2". I.D. of heim joint is 5/8". NOS OEM CSC and fits Champion Sidecar frames also and most American made sidecars. Powder coat is scratched from storage.
Free shipping in the USA.
email me for world wide shipping cost.
70 degree sidecar boss mount with heim joint is used with either the 90 degree adaptor or the 2" offset or a 45 degree clamp or 70 degree clamp to reach the motorcycle mount at the right angle and connect the heim joint to the lower clevis mount on the motorcycle. Generally it is a combination of two or three slip tube mounts that are needed to get the right wheel lead and angles to attach the heim joint to the motorcycle mount.
O.D of tube is 1-1/2". I.D. of heim joint is 5/8". NOS OEM CSC and fits Champion Sidecar frames also and most American made sidecars. Powder coat is scratched from storage.
Free shipping in the USA.
email me for world wide shipping cost.
Motorcycle sidecar mounting subframe kits in stock for Harley-Davidson Touring and Softail models.
All mounts are New Old Stock California Sidecar parts.
I have some new mounting parts. email me if your interested in one of the parts.
Two new I-nuts. One with 1/2"-20 tpi for a shock mount. And other I-nut with 3/4"-16 tpi. I-nut is 1/2" thick with a 1/2" hole to attach strut. Clevis lower 1-1/4" U- clamp mount for heim joint. I.D. 3/4". Use 5/8" bolt.
Black powder coated bent strut with 3/4''-16 tpi ends. California Sidecar reproduction part.
Complete CSC bent strut with clevis ends. Reproductions --------------- --------------------------------------------------------
I have CSC OEM NOS mounting kits for Harley-Davidson Touring motorcycles from 1984 to 2001 and Softails mount for years 1984-2008 models.
All of the lower mounts I have will fit Champion Sidecars and many other American made late model sidecars that use a heim joint with a 5/8" bolt.
Call me if you need sidecar mounts for your motorcycle or sidecar slip tube and struts.
A box of CSC 2" offset clamps used in the sidecar lower mounts.
Below are a few parts of the mounting kits I have in stock.
CSC lower rear sidecar mount for a Harley-Davidson 1993-2001 FLHT.
Above is a CSC lower rear sidecar mount for a Harley-Davidson FLHT 1984 to 1992 models. Clevis I.D. is 3/4" with a 5/8" bolt hole. Will also fit Champion Sidecars.
Below is the upper rear mount for a 1997-2001 FLHT. The I-bolt mount goes in the lug.
CSC Harley-Davidson FLHT lower front sidecar mount. This is mounted behind the floorboard. Will also fit Champion Sidecars as they use a heim joint mount too.
Calfornia Sidecar Harley Davidson FLHT 2002-2007 upper rear motorcycle sidecar mount, sold out.
California Sidecar Harley-Davidson FLST Softail, motorcycle sidecar mounting kit pictured above. I am out of the large Z-bar lower front mount but I have the other 3 mounts in stock.
California Sidecar Honda Goldwing 1500 motorcycle sidecar mounting kit, Sold Out. They will never be made again.
Not pictured is the upper front U-clamp mount which I do have in stock. I do have the GL 1500 installation manual for this sidecar mounting kit.
California Sidecar Honda Valkyrie motorcycle sidecar mounting kit. This only fits the older Valkyrie model from 1997 to 2003.
Sold Out! I do not have any more Valkyrie sidecar mounting kit. They will never be made again.
View our new 2021 sidecar parts and mounts catalog Here or down load it. 69 pages with lots of pictures.
Florida Sidecar Products
9038 S.R. 52
Warehouse
Hudson, FL
United States
ph: 1-727-856-2836
Mark